Bad Boy Wifi Antenna
. treme Hi-Power Wi-Fi Antenna Installation and Operation Guide Models covered: BB-XARC75 (Rail / Flat Surface) BB-XASC75 (1-14 Adapter) BB-XABC75 (Backstay) BB-XAPC75 (Pole) Rail mount shown Revision: 1.6a Getting YOU on the web. Declaration of Conformity Bitstorm declares that this Bitstorm BAD BOY device is in compliance with the essential require- ments and other relevant provisions of Directive 1999/5/EC.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two con. No part of the specifications may be reproduced in any form or by any means or used to make any derivation such as translation, transformation or adaption without permission from Bitstorm Inc. Copyright © 2013 Bitstorm Inc.
The Bad Boys are the new kid on the Wi-Fi block, bringing you high power devices to get you connected. The biggest problem is often the line of sight that's needed.
- The Best Long-Range Onboard WiFi. Other WiFi antennas use a USB connection which loses speed when the cables are. Bad Boy claims to have a range of.
- Wi-Fi and the Bad Boys of Radio. Alaska, where he honed his problem-solving skills as DJ and repairman and as an erector of a high-wind antenna.
All rights reserved. Bitstorm Inc.
Bad Boy Xtreme Chapter 1 - Bench Test Check off items as completed. Step 1 Remove the protective cap from Antenna connector and attach to Xtreme.
Power Injector Duo S15.5
Finger tight is adequate. Do not over tighten. POE Adapter Port 1. See illustration previously for location. Note: Xtreme requires power to operate and should be connected to Port 1 which always supplies power. Caution: Do not connect anything other than Bitstorm BAD BOY devices to Port 1.
Avoid the use of a staple gun – if the insulation is pierced, the cable can be rendered useless. The cable transfers digital data, so there is no need to remove excess cable.
Bitstorm recommends coil- ing and securing any extra cable. Bitstorm Inc. Bad Boy Xtreme sparingly to the contacts of the device cable end connector. Note: A thin coating of corrosion inhibitor is all that is needed. Too thick may result in floating connector pins and poor connections. Put the Xtreme’s cable end through bottom cover and plug into Xtreme. Bitstorm Inc.
Testimonials
Bad Boy Xtreme LED is lit on Port 1. NOTE: If Port1 and Port 2 yellow LEDs are lit, the DC Power Cable connections are reversed. Plug the Xtreme’s cable into Port 1. Observe green Power LED on Xtreme. Bitstorm Inc. Bad Boy Xtreme Step 3 Refer to Fig 2. On the Link Setup tab, select a hotspot from the list or enter an access point name into the Hotspot Name field 1.
Enter Wire- less Security settings as required 2. Select the country that you are in 3.
Devices & Systems
Bitstorm Inc. Bad Boy Xtreme Step 4 When Apply has completed, the Status tab will be displayed.
Connec- tion progress will be reported. You may see status of ’Connecting’, ‘Authenticating’, ‘Obtaining IP Address’, etc. Note: If connecting to an unsecured hotspot, additional authenti- cation after connection may be required by the hotspot. Bitstorm Inc.
Bad Boy Xtreme Appendix A - Specifications Output Power with Antenna: Up to 36 dBm (4W) EIRP max Receiver Sensitivity: up to -98 dBm Wireless Range: Line-Of-Sight, 5 miles (8 km) Operating Temperature: -4°F to +158°F (-20°C to +70°C). Bitstorm Inc. Bad Boy Xtreme Appendix C - Power Injector DUO Specifications M-POE-DUO-NS M-POE-DUO-S15.5 Injector 10-20 Vdc 5-30 Vdc Power Input: Injector Input -.5V, 2A max 15.5 Vdc, 1A max Power Output: Capacitor Output Ripple.